220 volt setup

In the next step, check the gauge wires; if you have gauge wires, then you have the option to connect new V to 15 or 20 amp receptacles. Now attach the black wire to the brass terminal screws and then connect the white wire to the nearest chrome screw and connect the green wire to the ground and screw it.

If you face difficulty making connections due to too heavy wires, it is the best option to run the new 12 gauge wire and two conductor cables. It will make your job easier when installing a new electrical box with the older electric box. Now splice the ground wire , white wire and black wire and screw wire cap onto each one, and hook it up with a new receptacle in the new electrical box.

After completing the new receptacle installing job, return to the main panel and pull out the main circuit controlling breaker. After pulling out the main breaker, disconnect all the existing wires, but be careful, immediately cap the red wire, and safely enter it back into the panel. Then connect the white wire and ground wire with neutral bus and ground bus, respectively. In the end, you will need to connect the remaining black wire to the single-pole breaker with its capacity of 15 or 20 amp.

Push it into the remaining slot on the double-pole breaker, and then install a cover plate over the free slot. It is done, and you can now turn on the breakers and use the receptacle for V. Two hundred twenty V volts current is suitable for high energy appliances, but when you need less power appliances, such as for V, it is not safe to use them on V.

You can wire V from V and can meet your need. While most of the world uses volt electricity, the United States uses a combination of v and v appliances. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment.

Home Learn. How do I install a volt outlet? Share on Facebook Share on Twitter. Table of Contents. How do I reset my Bluetooth headset? How do I fix the Le code on my LG dishwasher? Share Pin Tweet. Previous Post Why is my Samsung remote not working? Next Post What would cause a TV screen to go black? Never work on your electrical system while the power is still on. Doing so could result in serious injury or death.

Use a contact voltage tester on the wires inside your circuit breaker box to see if they still have power if you want to double check if they have a current through them. Use a drywall saw to cut through your wall along the outline you drew so that you can set the outlet box inside. Deeper outlet boxes work best since you have to hide multiple wires inside of them. You can also choose to mount the outlet box directly on your wall, which may be easier if you have cement or brick walls.

Measure the distance from the circuit breaker box to where you want to place the outlet. Find the shortest route from the hole you cut for the outlet to the main circuit breaker box in your home.

You may need to go through the floor or the walls in your home to find the shortest route. Extend a tape measure from the outlet box along the path you chose to the circuit breaker box and record the measurement.

You may need to take multiple measurements depending on the layout of your home and the obstacles between the outlet and circuit breaker box. Once you are certain you have the right amount of cable, use a pair of wire cutters to cut through the ends of the cable. You may also use 8-gauge wires if for your outlet if you want.

Drill or cut a hole near your circuit breaker box so you can run the cable to it. Install electrical conduit between the breaker box and the hole you drilled. Wires for lines cannot be exposed outside of your walls since they could easily get damaged, which could cause serious injury or death. Get enough rigid metal conduit to run from the side of the breaker box to the hole you cut and attach it to your wall using conduit straps every 1—2 feet 30—61 cm.

Fish the cable through the walls between the outlet and breaker box. Use a fish tape, which is a long flexible cable with a hook on the end so you can easily pull wires and cables through your wall. Feed the fish tape into the hole near your circuit breaker box and push it through toward the hole you cut for the outlet box. Go back to your circuit breaker box and reel in the fish tape so it pulls the cable with it back through the hole. You can buy metal conduits from your local hardware store.

Screw the outlet box into the wall so it stays in place. Part 2. Pull the wire stripper toward the end of the cable to cut through the outer coating and expose the wires inside.

Pull the wire stripper toward the end of the wire to cut off the insulation. Repeat the process for the other 3 wires that were inside the cable. Feed the white wire into the slot with the neutral screw on the outlet. Use a screwdriver to tighten the screw and clamp the white wire in place. Attach the green wire to the grounding screw on the outlet. Put the black and red wires into the hot ports on the back of the outlet. There will be 2 unlabeled screws left on the back of the outlet, which are known as the hot screws.

Place the end of the black wire in the port next to one of the unlabeled screws, and the red wire in the port on the other. Push the wires and outlet into the box so you can screw it in place. Bend the wires so they can fit in the back of the box. Push the outlet in front of the wires so the screw holes on the outlet line up with the ones along the sides of the box.

When you need to access the wires, unscrew the wall plate so you can get to them. Part 3. Remove the safety panel from the front of the box.

The safety panel on your circuit breaker box is the cover that hides all of the wires and breakers inside. Locate the screws around the edges of the circuit breaker box and rotate them counterclockwise to loosen them from place. This could cause to get electrocuted. Take out the circular knockout on the side or top of the circuit breaker box. Inspect the sides or top of the circuit breaker box to look for a circular piece that has a precut edge around it, also known as the knockout.

Be sure to use a drill bit meant for metal. Put a cable clamp in the hole you just knocked out. Get a cable clamp that matches the size of the knockout on your circuit breaker box, and slide the clamp through the hole. Screw the locking nut onto the threaded end of the clamp to hold it securely against the box. Feed the wires from the cable through the clamp into the box. Pull the wires into the box completely so you have 1—2 feet 30—61 cm of wire to work with. Install a amp double-pole breaker on the circuit.

A double-pole breaker allows twice the power to run through it as a standard amp single pole breaker, and takes up the same space as 2 single-pole breakers. Find a spot along the line of other breakers where the double-pole breaker will fit. Push in the top of the breaker into the metal clips inside the box so it snaps into place before pushing the bottom into place.

Make sure you get a breaker that matches the circuit breaker box brand you have. Make sure the breaker is off before you install it. Push the ends of the red and black wires in both ports of the breaker. Take the ends of the black and red wires and feed one of them into each of the ports.